', '

Download Wavecom W-code Digital Data Software Decoder For 17 BEST

Download Wavecom W-code Digital Data Software Decoder For 17 BEST

DownloadDOWNLOAD (Mirror #1)


Download Wavecom W-code Digital Data Software Decoder For 17

We made a new release for our decoder W-CODE W74PC, W-PCI and W-PCIe and W-PCIe. Main features in this release are: W74PC: we have improved the frequency control of W74PC, now each sample is send and received until a sample is sent, but the sample is hold until it is accepted from the receiver. This way you get a better control over the speed of the transmission and the samples are delivered with a more accurate time (with a typical error of 50-100µs). FT8 mode in on TFT 10kHz mode (with 20kHz sample rate). Basic support for IMMO and IMMO2 (digital token protocols) on W-PCI and W-PCIe. We had to change the syntax of the LUT download to support IMMO2 protocol, you can download the update for free. The MTK includes patches to IMMO and IMMO2.

We made a new release for our decoder W-CODE W74PC, W-PCI and W-PCIe. Main features in this release are: We have implemented SDT on the W74PC, you can configure the SDT on the W74PC, e.g. frames with 10ms at 100x20kHz, frames with 1ms at 100x200kHz and 100x10kHz, frames with 0.1ms at 100x10kHz with very good results. We decoded the British APT 7256 OFB datasheet and compared the result with an FMS11. We delivered several componants and a complete decoder in software for ADS-B system and a new device is in production.

Wavecom released a new version of their w-code decoder W71PC. Main features of this release are the following: We have implemented a new option for the transmission of frames to the W71PC, which was the only feature in the current w-code for analog transmission, that has not be implemented. With this new features you can transmit frames on IF and AF of 576, 704, 960 and 1280 channels. You can transmit 250 frames on 672 channels. W71PC can now transmit frames on a single analog input connection. In this version the an FMS11 has been evaluated and we included a table of how to get an 2.5V <--> 1V compatible output if needed in the software section. A new example for the M74IX-DALVD is included and a new, shorter instruction for the ScadaLab webm (new version of the M74IX-DAUPDEAS). Newly implemented is a serial connectivity and the possibility to transmit frames on 144 channels with a compressed format. Also the possibility to transmit frames on USB to the W71PC. Regarding to the compression formats for the compressed frames you can send frames with a peak value below 1 volt, too. This is the lower limit for any analog frames, because we lose about 1V with this channel protection.

link 11 is used to exchange digital information among airborne, land-based, and ship-board tactical data systems. it is the primary means to exchange data such as radar tracking information beyond line of sight. in addition, it is used for radar coordination and weapons fire control. the w-code digital data link is a single-channel link-11 wired packet data link, used by the british armed forces primarily for intercoms, comms, and maritime tactical data exchange. as such it can also be used to transmit/receive/decode/encode analogue data from/to the user. it was previously known as the tadil-a link. data is transmitted over the link using a payload mode of operation called the w-code protocol. there is no subscriber address or control messages, and no control channel, just the data itself. the information transmitted is in the form of control code frames and the w-code data frames. these frames are sent in groups of control code frames, data frames, and data link control frames. the control code frames are two to four bytes in length. these frames may be used by the receiving side to identify the type of data that follows, in addition to initiating or closing the link. the data frames are either 4 to 8 bytes in length, or 32 to 64 bytes in length. these frames carry the data that is being exchanged. the data link control frames are used to indicate to the receiving side the availability of data. the w-code data link protocol is described in mil-std-188-203-1a, and can be used to carry signals in any standard frequency band, as long as the transmitting and receiving equipment are calibrated to the correct frequency band. 5ec8ef588b


Status: online ✅ (12 hs ago)

Leave a Reply

Your email address will not be published.

Up Next:

A Little Agency Little Melissa Pictures 📢

A Little Agency Little Melissa Pictures 📢